Mazak Laser Technology | Global Leader in CNC & Fiber Laser Systems Get a Free Quote

xTool S1 Laser Cutter: Specs, Cleaning, Metal & Glass Marking, and Free Engraving Files That Work

I run production at a small laser engraving shop. I've handled 180+ rush orders in three years, including same-day turnarounds for event and trade-show clients. We've pushed the xTool S1 through most of them. Here's the FAQ I wish existed when we bought it.

What are the real xTool S1 laser cutter specs — and which numbers actually matter?

The S1 is a diode laser, not a CO₂ unit. That distinction matters more than any single spec on the box. You're looking at 10W, 20W, or 40W interchangeable modules depending on which kit you buy. The working area is 498 × 319 mm (roughly 19.6 × 12.6 inches). It's a fully enclosed Class 1 laser — which, honestly, is the reason we bought it over an open-frame unit.

According to xTool's published specs, the 40W module cuts 1/8-inch plywood in a single pass at a reasonable speed. Thicker material requires multiple passes, and here's where the marketing gets fuzzy: "cuts through 1/4-inch wood" usually means multiple passes with clean air assist and perfectly focused optics. I'm not 100% sure why xTool doesn't publish a simple single-pass vs. multi-pass table — it would save everyone a lot of test material.

Power consumption sits around 200W during operation (not counting the exhaust fan). That's probably fine for a small shop, but check your circuit load if you're running multiple machines on the same breaker.

Can the xTool S1 actually mark metal, or is that just marketing?

It can — with caveats. Bare stainless steel or aluminum won't mark directly without an additive. We use a laser marking spray (CerMark-style compound) for bare metals, and it works well for small runs. Anodized aluminum, coated brass, and painted metal surfaces mark directly because the laser is removing a surface layer.

What it won't do is cut sheet metal or engrave thick metal in any meaningful way. The 40W diode doesn't have the power density for deep metal engraving. If a client needs deep metal engraving, we send it out to a fiber laser shop. That's not a weakness of the S1 — it's just physics. If you're shopping for a laser marking machine for metal, the S1 is not that machine unless your "metal work" is surface marking only.

How do you clean an xTool S1 without destroying the lens?

Cleaning the xTool S1 is the single most overlooked maintenance task, and it's the fastest way to ruin an expensive lens. Our routine, built from two years of trial and error:

  • After every heavy-residue job: wipe the protective lens cover with 99% isopropyl alcohol and a lens tissue. Don't use regular paper towels — they can scratch.
  • Weekly: check the main lens for haze. If you see cloudy residue, clean it immediately. A hazy lens becomes a cracked lens faster than you'd think.
  • Monthly: vacuum the honeycomb bed and clean the exhaust fan intake. Ash buildup is a fire risk (note to self: we learned this the hard way in early 2023).
  • Never: touch the lens surface with bare fingers. Oils etch into the coating permanently.

I went back and forth between a strict lens replacement schedule and cleaning on condition for months. We now replace the protective lens every six months and clean on condition in between. The protective lens costs more than a cleaning kit, but it's cheaper than replacing the module.

Does the xTool S1 engrave glass without cracking it?

Yes, but laser marking glass is finicky. You're not really engraving — you're etching the surface with controlled microfractures. The key is low power, high speed, and a wet surface. We use a soapy water film over the glass, or wet paper laid flat. This keeps the glass cool and reduces the chance of thermal shock.

Small lettering and simple logos work well. Deep carving does not. And don't expect clear results — glass etching comes out frosty. If a client needs deep, polished glass engraving, that's a sandblasting or rotary tool job.

Where do you find free laser engraving files that actually work on the S1?

Free laser engraving files are everywhere, but maybe 60% of them are designed for CO₂ lasers with different power curves. Our go-to sources:

  • Thingiverse: Search "laser engraving" and check the license. Many are Creative Commons but not commercial-safe.
  • Instructables: Good for SVG templates, but test on scrap first.
  • Etsy free files: Sellers sometimes offer low-res freebies designed to upsell. Fine for personal use — check the commercial license.
  • xTool's own file library: Designed for their power specs, so less fiddling with settings.

The real issue isn't finding files — it's lighting and power settings. A file that looks perfect in preview can blow out edges or under-burn in reality. If I'm not sure about a file, I always test on a 3-inch square of the same material before committing to a full batch. In my experience, that one habit prevents more waste than any file-quality filter.

What happens when your laser dies 36 hours before a rush job?

It's happened. In March 2024, a client needed 200 engraved acrylic awards for a conference — 36 hours out — and our main S1 threw a lid sensor error. Normal turnaround is five business days. We had two options: find a backup machine or push the client's deadline (not an option).

We called a local maker space that had an S1 (lucky break), drove the files over, and ran the batch overnight with their exhaust fan on a makeshift extension. Paid $180 for the access time and a pizza for the lab manager. The client never knew. But it could have been a $15,000 penalty clause for the event organizer.

That's when we bought a second S1 — not because we need two production machines, but because the downtime risk wasn't worth saving the $1,200 on a used unit. If you're running client work on a single diode laser, budget for a backup or establish a relationship with a local shop that can absorb overflow. Emergency vetting is cheaper than emergency renting.

Is the xTool S1 the right machine for a small business?

Depends on what you're cutting — and what you're not.

It's great for: small-batch custom work (wood, leather, acrylic, coated metal), makers selling at markets, and shops that need enclosed, safe laser operation without a dedicated CO₂ setup.

It's not built for: high-volume production (it's slower than CO₂), thick metal cutting, or industrial materials. If that's your core business, don't buy the S1 and hope it keeps up. Look at a fiber laser for metal or a CO₂ for thick acrylic and wood production.

The vendor who says "this machine does everything" is lying or doesn't know their own product. The S1 does a lot well. It doesn't do everything. That's fine — knowing those boundaries is what keeps your shop profitable and your clients coming back.

Share this article:
author-avatar
Jane Smith

I’m Jane Smith, a senior content writer with over 15 years of experience in the packaging and printing industry. I specialize in writing about the latest trends, technologies, and best practices in packaging design, sustainability, and printing techniques. My goal is to help businesses understand complex printing processes and design solutions that enhance both product packaging and brand visibility.

Leave a Reply