Quick context: I'm the office administrator for a 35-person company. I handle supplier management and purchase orders — not laser operation. When our design team asked for an engraver last year, I was the one doing vendor research and writing the justification memo to finance.
So I know enough to be dangerous, not enough to sound like an expert. These are the questions I got — from our team, from finance, and from other admins in my networking group — plus the answers I've landed on after nine months of having one in the back room.
1. What can the xTool S1 actually do?
Short answer: it's a diode laser engraver that handles wood, leather, glass, anodized metal, and certain acrylics. In our shop, the design team uses it for engraved client gifts (walnut, leather notebooks), custom signage, and a surprising amount of sample work on anodized aluminum. That covers maybe 90% of what they need it for.
The other 10% falls into a gap. A diode laser is not the same tool as a CO₂ laser or a plasma cutter — different light wavelengths, different capabilities, different price brackets. If I were buying a tool laser engraver just for personalization and prototyping, this class of machine is a no-brainer. If the plan is to cut heavy steel plate, I'd be looking somewhere else entirely.
2. How much power does the xTool S1 consume?
I don't have hard data on every module variant, but based on our own metering, the 20W unit sits around 150–170W under load. The 40W draws more — roughly 250–280W by my estimate. Standby is minimal, under 30W. Our electricity here runs about $0.13/kWh, so even heavy weekly use adds only a few dollars a month.
What I wish I'd tracked more carefully: actual runtime hours per module. We log orders, not machine hours, so my numbers are anecdotal. If your facility charges back cost to departments, keep a log — I had to reconstruct a quarter of usage from project emails, which was a mess.
3. Can the xTool S1 cut metal?
This one I get asked most, and the honest answer is: it depends on the metal and what you mean by "cut."
Engraving? Yes, on anodized aluminum, stainless steel, brass, and similar. Cutting? Very limited. You can cut thin foil-like metal (under 1mm, and even then only on certain alloys with multiple passes), but bending a metal-cutting job onto this machine is a classic mistake. The 40W module helps, but it doesn't break physics. For anything over roughly 1mm of ferrous metal, you want fiber laser territory or a plasma cutter.
This is where I'd flag the limitation openly: if metal cutting is your primary need, don't buy a diode laser engraver expecting it to be a metal cutter. Buy the right tool for the primary job.
4. How do you cut acrylic sheets?
The design team cuts acrylic for signs and display pieces. A few practical notes from watching them do it:
- Cast acrylic, not extruded. Extruded acrylic melts into a gummy mess on the cut edge. Cast cuts cleaner and engraves with a nice frosted-white look.
- Dark or opaque colors behave better than clear. Clear acrylic lets the laser pass through without engaging, so you get inconsistent results. If clear is a must, mask the surface first.
- Ventilation is non-negotiable. Acrylic fumes are rough. We routed the exhaust out a window and added an inline fan; the difference before and after was night and day.
- Multiple passes beat one high-power pass. Slows the job down, but edges come out cleaner and there's less risk of flame flare.
How do you cut acrylic sheets at larger scale? You don't on an S1 — you'd move to a CO₂ bed. For our sizes (up to about 400×400mm pieces), this machine is fine.
5. Would a plasma cutter be a better fit?
Depends on what you're cutting. A plasma cutter uses ionized gas to cut conductive metal — it's fantastic on plate steel, aluminum, and stainless, typically from about 1/8" up to an inch or more depending on the machine. It doesn't touch wood, leather, acrylic, or glass.
Our shop needed a mixed-material tool for customization work, which is why we went with the laser. If your workflow is metal fabrication — welding shop, HVAC, structural — a plasma cutter earns its keep and the xTool S1 would just sit there. Different tool, different job. Anyone who tells you one replaces the other is selling something.
6. Which configuration should a small business buy?
If I were doing this purchase again, I'd skip the 10W and start at the 20W. The 10W is fine for engraving, but the moment you want to cut 5mm plywood at a reasonable speed, you'll be annoyed. The 40W is the sweet spot for mixed wood and acrylic work, at a real cost premium.
Accessories that earned their price: the air assist (huge difference on cut quality), and the honeycomb panel (less underside char). The rotary I'd call situationally useful — we use it for tumblers, but only a few times a quarter. Skip it unless you know you have tube-shaped work lined up.
7. What would I tell another admin looking at this?
Three things. First, budget for ventilation and a dedicated table — the machine is one line item, but the setup around it is where surprise costs hide. Second, get the delivery person to bring it inside; ours weighs more than the two of us could comfortably lift. Third, and this is the honest limitation one: if any single person on your team is buying this for "one specific project," push back. Ask what project two looks like. If there isn't one, rent time on a maker-space machine first. We nearly bought ours for a project that evaporated six weeks later — the team was embarrassed but the machine has since paid for itself on recurring client work.
Pricing note: everything above reflects our Q3–Q4 2024 purchase and usage. Laser pricing moves fast, so verify current quotes before you put numbers in a budget memo. Specs across the 10W/20W/40W modules are worth a fresh check too — this market iterates faster than most of the office supplies I used to buy.
Leave a Reply